Three power scenarios. One coordinated delivery path.三大电力应用场景，一体化协同交付。
Explore equipment architectures for industrial distribution, standby generation and public infrastructure. Each configuration is reviewed against the actual project specification.面向工业配电、备用发电和公共基础设施，梳理设备架构与工程接口。每套配置均需依据实际项目技术规格审核确认。
10–35kVDistribution support配电项目支持
18 seriesGenerator catalog发电机组系列
MV / LVSystem coordination系统接口协调
FATInspection planning工厂检验计划
01 / INDUSTRIAL DISTRIBUTION工业园区配电
Industrial park power distribution工业园区配电解决方案
Coordinate the transformer, MV/LV switchgear, reactive-power compensation, compact substation and 10kV engineering interface as one project package.统筹变压器、中低压开关柜、无功补偿、箱式变电站与10kV工程接口，形成一体化项目配套。
01
Equipment architecture for industrial and manufacturing sites工业与制造业项目设备架构示意
20KV · SC(B)14
Power transformers电力与配电变压器
Oil-immersed distribution and dry-type options are reviewed against load profile, installation environment and project voltage.结合负载特性、安装环境及项目电压要求，审核油浸式配电变压器与干式变压器选型。
Capacity and voltage ratio容量与电压比
Loss and temperature-rise targets损耗及温升目标
Indoor or outdoor installation室内或室外安装
KYN28 · GCS · GGD
MV/LV switchgear中低压开关成套设备
Review incoming and outgoing circuits, busbar ratings, protection coordination and cabinet interfaces.审核进出线回路、母线额定参数、保护配合及柜体接口。
12kV MV distribution12kV中压配电
400V LV distribution400V低压配电
Protection and interlocking保护与联锁
GGJ
Power quality and compensation电能质量与无功补偿
Select compensation capacity and switching strategy using the measured or forecast load and harmonic profile.依据实测或预测负载及谐波情况，确定补偿容量和投切方式。
Power-factor target功率因数目标
Harmonic assessment谐波评估
Monitoring interface监测接口
YB · 10kV EPC
Compact substation and EPC箱式变电站与工程配套
Integrate transformer and distribution equipment in a prefabricated enclosure, with cable, testing and handover support as required.按需将变压及配电设备集成于预装式箱体，并配套电缆、测试与交接支持。
Site layout场地布置
Cable and grounding电缆与接地
FAT/SAT planning工厂与现场测试计划
Engineering specification checklist工程技术参数清单
System voltage系统电压10kV / 0.4kV reference; confirm grid interface以10kV／0.4kV为参考，按接入条件确认
Transformer selection变压器选型Capacity, losses, temperature rise and installation核对容量、损耗、温升及安装方式
Switchgear coordination开关设备配合Rated current, short-circuit level and protection核对额定电流、短路容量及保护配合
Power quality电能质量Compensation target after load and harmonic review负载及谐波审核后确定补偿目标
Engineering note工程提示Key inputs: single-line diagram, load list, voltage and frequency, short-circuit level, ambient conditions and applicable standards.关键输入：单线图、负载清单、电压与频率、短路容量、环境条件及适用标准。
02 / STANDBY & EMERGENCY POWER备用与应急电源
Standby and emergency power备用与应急电源解决方案
Build a practical backup-power architecture around generator capacity, starting sequence, ATS logic, noise limits and runtime requirements.围绕机组容量、启动顺序、ATS切换逻辑、噪声限制和续航需求，形成可执行的备用电源方案。
02
Industrial diesel generation and transfer coordination工业柴油发电与切换系统配套示意
13 SERIES
Diesel generator sets柴油发电机组
Kangwo, Yuchai, Weichai, Cummins and Tellhow series can be evaluated by model-specific prime or standby ratings.可按具体型号的主用或备用功率，评估康沃、玉柴、潍柴、康明斯和泰豪系列。
Load-step and starting demand阶跃负载与启动需求
Fuel and runtime plan燃油与续航计划
Factory load testing工厂负载测试
ATS · AMF
ATS and control coordinationATS与控制系统协调
Define mains-failure detection, generator start, transfer, return-to-mains and electrical/mechanical interlocking in the approved control narrative.在确认的控制逻辑中明确市电失电检测、机组启动、切换、市电恢复及电气／机械联锁。
Transfer sequence切换顺序
Interlock scheme联锁方案
Remote monitoring远程监控
0.9–12kW
Gasoline generator sets汽油发电机组
Yuchai Agricultural open-frame, silent and inverter series support temporary power needs, with rated output, frequency and phase selected by model.玉柴农业开架、静音和变频系列可用于临时供电，按型号核对额定功率、频率及相数。
Output and phase selection输出及相数选择
Site operating conditions现场运行条件
Safety and maintenance安全与维护
Engineering specification checklist工程技术参数清单
Generator duty机组工况Prime or standby rating and load-step requirements主用或备用功率及阶跃负载要求
Transfer control切换控制ATS sequence and interlocking to approved drawings依据确认图纸确定ATS顺序与联锁
Fuel and runtime燃油及续航Size from site duty cycle and storage limits根据现场运行周期及储油限制确定
Testing evidence测试资料Load test, control test and FAT scope as agreed按协议确定负载、控制及FAT测试范围
Engineering note工程提示Transfer time, acoustic performance and runtime are project-specific and must be confirmed in the final equipment and control specifications.切换时间、噪声表现及续航能力均依项目而定，须在最终设备和控制技术规格中确认。
03 / INFRASTRUCTURE & UTILITIES基础设施与公用工程
Infrastructure and public utilities基础设施与公用工程解决方案
Combine compact distribution equipment with environmental protection and maintainability for transport, water and municipal projects.针对交通、水务及市政项目，将紧凑型配电设备与环境防护、可维护性要求一并考虑。
03
Ring main unit and compact distribution equipment环网柜与紧凑型配电设备示意
ZDFW · ZDC
Ring main units and switching stations环网柜与开闭所
Review 12kV RMU configurations, switching duty, protection, automation and enclosure requirements for the site environment.按现场环境要求审核12kV环网柜配置、开断任务、保护、自动化及外壳防护要求。
Rated voltage and current额定电压与电流
Ingress protection防护等级
Automation interface自动化接口
YB-12/0.4
Prefabricated compact substations预装式箱式变电站
Coordinate the high-voltage, transformer and low-voltage compartments against available space, ventilation and access needs.结合可用空间、通风与检修需求，协调高压室、变压器室和低压室的布置。
Footprint and access占地与检修通道
Thermal management散热管理
Civil interface土建接口
SC(B)10/13/14/18/H15
Dry-type transformers干式变压器
Assess dry-type options for indoor installations, including insulation, ventilation and fire-safety requirements.针对室内安装场景评估干式变压器，并核对绝缘、通风和消防要求。
Indoor environment室内环境
Insulation class绝缘等级
Applicable fire requirements适用消防要求
Engineering specification checklist工程技术参数清单
MV distribution中压配电12kV RMU family; final rating per grid requirements12kV环网柜系列，最终参数依电网要求确定
Environmental protection环境防护Ingress, flood and corrosion rating by site assessment根据现场评估确定防护、防洪及防腐等级
Automation自动化Monitoring and control interface to owner system核对与业主系统的监测控制接口
Safety and access安全与检修Fire requirements, ventilation and maintenance clearance核对消防、通风及检修间距要求
Engineering note工程提示Flood exposure, corrosion class, enclosure protection and fire classification require site-specific engineering review and verified product documentation.洪水暴露、腐蚀等级、外壳防护及防火等级应依据现场条件进行工程审核，并以核验后的产品文件为准。
PROJECT TECHNICAL REVIEW项目技术审核
Start with your single-line diagram and site conditions.从单线图与现场条件开始。
Send the voltage, load list, equipment scope, operating environment and target standards. Our team can coordinate equipment selection and the documentation needed for your project review.提交电压、负载清单、设备范围、运行环境及目标标准。我们可据此协调设备选型与项目审核所需资料。
Single-line diagram项目单线图Load and capacity负载及容量Location and standards地点与标准Delivery schedule交付时间
ENGINEERING RFQ工程询盘
Request a project-specific equipment proposal获取针对项目的设备配套建议
Use the existing inquiry form to upload your project SLD and prepare your request. No unverified response-time or certification claims are implied.通过现有询盘表上传项目单线图并提交需求。具体技术指标以最终确认文件为准。
